ISO 7919-5 PDF

IS/ISO (): Mechanical vibration – Evaluation of machine vibration by measurements on rotating shafts, Part. 5: Machine sets in hydraulic power. DIN ISO [ Withdrawn ]. Mechanical vibration – Evaluation of machine vibration by measurements on rotating shafts – Part 5: Machine sets. Purchase your copy of BS ISO as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards.

Author: Vogul Zolok
Country: Gambia
Language: English (Spanish)
Genre: Politics
Published (Last): 12 August 2004
Pages: 89
PDF File Size: 16.86 Mb
ePub File Size: 8.90 Mb
ISBN: 558-4-70651-286-3
Downloads: 99802
Price: Free* [*Free Regsitration Required]
Uploader: Yokasa

79195 vibration value measured at the bearings and their supports, which are rigidly embedded in the building, is sometimes produced by hydraulic forces, directly transmitted from the hydraulic machine via the foundation, and is not produced by radial shaft vibration.

Change In vibration magnitude In some cases, a significant i. Machine sets covered by this part of ISO include a combination of — hydraulic turbines and generators, — pumps and electrical machines operating as motors, — pump-turbines and motor-generators, and — hydraulic turbines, pumps and motor-generators classic pump-storage machine setsincluding auxiliary equipment e.

Both quantities are measured in the radial direction at, or close to, the main load-carrying journal bearings at rated speed s under steady-state operating conditions as io in 4.

Under 79199-5 conditions especially for rotor arrangements with only two radial bearingsresonance-like phenomena can be observed at certain speeds while decelerating, with 7919-55 containing one or more of the natural frequencies of the rotor corresponding to the instantaneous speed At frequent transient operating conditions, such as start-up and shut-down, random excitations with broad- band spectrum are dominant.

Copyright BIS has the copyright of all its publications. Need more than one copy? Such equipment is capable of determining the trends of vector changes that occur in individual frequency components of the vibration signal. The total area of vibration magnitudes, shown in Figures A. Proceed to Checkout Continue Shopping.

BS ISO 7919-5:2005

The choice of range A or B depends, however, on the relationship between the new excitation forces and the capacity of the new and re-used components to withstand long-tenn dynamic exposure. Machine sets in hydraulic power generating and pumping plants Status: You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server.

Higher values of vibration may be permitted at other measurement positions and under conditions described in Annex B. Maschinensaetze in Wasserkraft- und Pumpenanlagen. Outside of the normal load range of the hydraulic machine, the radial forces increase strongly especially during transient conditions.

  HOW TO SELL YOURSELF BY ARCH LUSTBERG PDF

Mechanical vibration – Evaluation of machine vibration by measurements on rotating shafts, Part 5: This is because changes in vibration magnitude, even though the specified limits are not exceeded, may point to incipient damage or some other irregularity. Coupied industrial sio [2] ISOMechanical vibration — Evaluation of machine vibration by measurements on non- rotating parts — Part 1: You may experience issues viewing this site in Internet Explorer 9, ixo or Where there is no established baseline, for example with a new machine, the initial ALARM setting should be based either on experience with other similar machines or relative to agreed acceptance values.

If the transducers are installed on the bearing support structure or bearing housing, as it is common for vertical machines, care shall 79919-5 taken that the relative motion between the bearing shell or pad and the transducer itself is small compared with the shaft motion. The widespread distribution of ieo and the statistical evaluation can be seen. Certain conventions are, however, not identical to those used in Indian Standards.

Standards Subsctiption may be the perfect solution. Frequencies to be expected are those close to the bending natural frequencies of the rotating system, B. They are based on a broad spectrum of theoretical and experimental investigations on horizontal shaft machines.

We have no amendments or corrections for this standard.

Vibration Standards > Turbo Monitoring

Recommended Standards The following standards are recommended by Turbo Monitoring for all turbomachinery operators: You may delete a document 79199-5 your Alert Profile at any time.

They will be added to a future edition of this part of ISO This leads to increased shaft motion – In contrast to thermal machines, hydraulic machines can normally be started up and shut down, or power can be changed rapidly and frequently. Part 1 General guidelines Degree of Equivalence identical The technical committee responsible for the preparation of this standard has reviewed the provisions of following International Standard referred in this adopted standard and has decided that they are acceptable for use in conjunction with this standard: The limiting values are applicable to ail kinds of turbine-driven machine sets, independent of type, head and power, under steady-state conditions, except for the restrictions stated in Clause 1.

ISOMechanical vibration of non-reciprocating machines— Measurements on rotating shafts and evaluation criteria — Parf 1: Machines with vibration magnitudes within this major range are considered acceptable 791-95 unrestricted long-term operation.

We use cookies to make our website easier to use and to better understand your needs. With regard to the transducer support structures, it is advisable that the lowest natural frequency of those vibration modes that create significant movements in the working direction of shaft displacement transducers be greater than seven times the synchronous rotational frequency, and should not be a direct multiple of the synchronous rotational frequency.

  GAUBLYS GAMTINE GEOGRAFIJA PDF

NOTE 1 The numerical values specified are not intended to serve as the only basis for vibration ixo since, in general, the vibratory condition of a machine is assessed by consideration of both the shaft vibration and the associated structural vibration see ISO and ISO Measurements were made on machines that had been running in normal operation for a long time without problems.

The values chosen will normally be set relative to a baseline value determined from experience for the measurement position or direction for that particular machine. In the case of extreme transients, occurring for example at failure of a shut-off valve, the intensity of this broad-band excitation spectrum increases even more.

This website is best viewed with browser version of up to Microsoft Internet Kso 8 or Firefox 3. Measurement task C requires the installation of transducers near to, or inside, the hydraulic machine seals or labyrinths, or at positions from where it is possible to reconstruct the shaft line deflection within the hydraulic machine for all relevant vibration modes.

They yield transfer functions for the different permanent measurement planes. Hydraulic machines are therefore often used for peak-load supply or for frequency and power control.

Evaluation des vibrations des machines par mesurages sur les arbres tournants. Condition monitoring and diagnostics of machines — Vibration condition monitoring. Condition 79199-5 and diagnostics of machines — Data processing, communication and presentation.

Criterion II is therefore specified on the basis of change in the total vibration value which may occur under steady and repeatable operating conditions, but it does not apply to those changes that are expected and occur as a result of changes in operating conditions.

With the improved data sets, the following steps in the described procedure using a software package for statistical analysis were performed see Reference [4]: In this adopted standard, reference appears to the following International Standard for which Indian Standard also exists. NOTE 4 Vibration magnitudes for recommissioned units with Increased output, usually characterized as “uprated’, can be located in range A or B.