Service manual for Epson Stylus Photo TX, TX, PX multifunction devices. Epson Stylus Photo TX Epson Stylus Pro and Pro Service Manual Epson Stylus Color PX TX TX Service Manual & Repair GuideEpson Stylus. [EPUB] Epson Stylus Photo Px Tx Tx Service Manual Repair Guide -. PDF Format. Book file PDF easily for everyone and every device. You can.

Author: Kajin Morn
Country: Cyprus
Language: English (Spanish)
Genre: Education
Published (Last): 22 January 2017
Pages: 59
PDF File Size: 3.3 Mb
ePub File Size: 4.61 Mb
ISBN: 878-3-31347-647-6
Downloads: 30749
Price: Free* [*Free Regsitration Required]
Uploader: Samull

Measure the voltage at the wall outlet. Head Cleaning Replace ink cartridge before cleaning print head. Extra mamual must be taken to avoid injury from sharp metal edges. Move the CR Unit by hand, and check to see if it moves smoothly. Removing the Upper Paper Guides 3 Figure Connect the external device.

It may require considerable time to clean if dirt sticks to the inside of the document table. Replace the PE Sensor. Scan to Memory Card Stores an image scanned by the scanner directly into a memory card.

Diagnostics when paper ejection is abnormal Condition Paper is jammed on the way of paper ejection. While performing the slide show, displaying number of copies, printing from an external device or from a computer cannot be made. Print Mode Monochrome Table Perform disassembly and assembly of the Scanner Unit in a clean room or on a clean bench to keep away from dust and dirt. Check tension of the timing belt. Revision C Take extra care not to contaminate the Timing Belt with grease.


If there is a problem, perform the part replacement once again.

Download Epson Stylus Photo TX/TX/PX Service manual. Epson Stylus Photo TX

While holding the Scanner Unit, remove the screws x7 that secure the Upper Housing. Specifying it for each of the images independently also can be made in the preview screen. Take care in handling the Lower Housing.

See Figure p. Printing a CD jacket on A4 or letter size paper is also provided. Let the printed pattern dry for more than 5 minutes if using CIS sensor type scanner. The combined Temperature and Humidity conditions must be within the blue-shaded range in Fig. Select the number of copy.

After replacing the Ink System Unit, be sure to perform the required lubrication. The Scanner Unit cannot be opened enough to use a general screwdriver for removing the screws that secure the Upper Housing; therefore, this section describes removing the Scanner Unit before removing the Upper Housing.

Restore the same memory card condition as it was when the index sheet was printed or print a new index sheet. Supply the normal power. Carriage Slide not moving properly Check to see if sufficient grease is remaining on carriage slide parts at back of main frame.

After routing the cables, secure them with acetate tape and double-sided tape as shown in Fig. Faulty connection of the connector Check the connection between the Power Supply Board Correct the connection.


Checking waste ink overflow Remove the Head FFC once and reinstall it properly. Data saving was not executed, since the memory card had been removed. Head cleaning was attempted in the Ink Low state. Press the Zervice button. Move the Driven Pulley in the direction of the arrow, and remove the Timing Belt. Stacker Cover Dowel Figure However, depending on the DSC, some of the settings may not be available.


As the memory card was write-protected, formatting failed. Bluetooth communication settings can be configured.

The carriage detects the voltage of the PW sensor at the carriage stop position the black area at the Paper Guide Front. Borderless Makes a copy with no white margins. Table of Contents Add to my manuals Add. Remove the screw that secure the grounding wire. Date and time information applied on DOS-compliant file system.

Epson Stylus Photo TX650 Manuals

Because for almost the same standerd as SDHC. Therefore, if a P.

Symbols Used In This Manual Use this to reset the counter after replacing the Waste Ink Pad. Rear right Route the tube with red line facing up Hinge Rib Figure Paper is fed normally Counterclockwise: Touching with your bare hand or adhering grease can cause nozzle clogging.

The PF Motor rotates clockwise while manuao